ME Labs, Inc. | 1-719-520-5323 | Example Program - PROGEE8X.pbp

' Name        : PROGEE8X.pbp
' Compiler    : PICBASIC PRO Compiler 2.6
' Assembler   : PM or MPASM
' Target PIC  : 40-pin 16F877A, 18F452 or similar
' Hardware    : LAB-X1 Experimenter Board
' Oscillator  : 4MHz external crystal
' Keywords    : HSERIN, HSEROUT, I2CREAD, I2CWRITE
' Description : PICBASIC PRO program to receive a HEX file from PC
' and write data to I2C memory. Writes data in page mode, 8 bytes at
' one time. Memory device must be addressed with 8 bits and capable
' of receiving 8 bytes at once.
'

' Define LOADER_USED to allow use of the boot loader.
' This will not affect normal program operation.
Define	LOADER_USED	1

' Set receive register to receiver enabled
Define HSER_RCSTA 90h
' Set transmit register to transmitter enabled
Define HSER_TXSTA 20h
' Set baud rate
Define HSER_BAUD  2400

scl    VAR PORTC.3  ' Clock pin
sda    VAR PORTC.4  ' Data pin
pinin  VAR PORTC.7  ' Serial receive pin
pinout VAR PORTC.6  ' Serial transmit pin

addr VAR BYTE       ' Memory Address
dta1 VAR BYTE[9]    ' Data array with location for checksum
bb   VAR BYTE       ' Byte count
tt   VAR BYTE       ' Record type
i    VAR BYTE       ' Loop counter
cs   VAR BYTE       ' Checksum
ln   VAR BYTE       ' Line count

   Clear            ' Clear RAM data
   ADCON1 = 7       ' Set PORTA and PORTE to digital
        
   ln = 0           ' Clear line count
   For i = 0 To 255 Step 8 ' Store $00 to first 256 locations (for testing)
      I2CWrite sda,scl,$A0,i,[STR dta1\8]
      Pause 10
   Next i

   HSerout ["Ready",13,10]    ' Notify: ready for file
        
mainloop:
   cs = 0    ' Reset checksum byte
   HSerin [WAIT(":"),HEX2 bb,HEX4 addr,HEX2 tt] ' Receive line and parse
   cs = bb + addr + tt        ' Begin checksum calculation
   If (tt = 1) Then eof       ' Check for end of file
  
   If (bb>8) Then             ' Write twice if more that 8 bytes of data on line
      For i = 0 To 7          ' Loop for first 8 bytes of data
        HSerin [HEX2 dta1[i]] ' Store each byte to location in array
        cs = cs + dta1[i]     ' Add each byte to checksum calculation
      Next i

      I2CWrite sda,scl,$A0,addr,[STR dta1\8] ' Write 8 bytes of data to device
      bb = bb - 8
      addr = addr + 8
   
      For i = 0 To (bb)	      ' Loop for remaining expected data-bytes and checksum
        HSerin [HEX2 dta1[i]] ' Store each byte to location in array
        cs = cs + dta1[i]     ' Add each byte to checksum calculation
      Next i

      If (cs <> 0) Then sume  ' Check for checksum error
      I2CWrite sda,scl,$A0,addr,[STR dta1\bb] ' Write remaining data to device

   Else                       ' Write once if 8 or less bytes of data      
      For i = 0 To bb         ' Loop for each expected data-byte and checksum
        HSerin [HEX2 dta1[i]] ' Store each byte to location in array
        cs = cs + dta1[i]     ' Add each byte to checksum calculation
      Next i
        
      If (cs <> 0) Then sume  ' Check for checksum error
      I2CWrite sda,scl,$A0,addr,[STR dta1\bb] ' Write data to device
   EndIf
            
   ln = ln + 1                ' Count line received
   Goto mainloop              ' Go get another line
        
sume:
   HSerout ["Checksum Error: line ",DEC ln,13,10]  ' Notify: checksum error
                
eof:
   HSerout [DEC ln," lines received",13,10]  ' Notify: Confirm line count

   For i = 0 To (ln*16)		' Loop 16 times for each line received
     I2CRead sda,scl,$A0,i,[cs]	' Read back each character
     HSerout [HEX2 cs]          ' Send each character
     If (i+1)//16 = 0 Then
        HSerout [13,10]	        ' New line every 16 characters
     EndIf                                   
   Next i

   HSerout [13,10,13,10]        ' New Lines

   End

           

Download the program file.